Weber Superflex D3 16 kg liquid (comp. A) two-component, flexible sealing micro-mortar

webertec Superflex D3 is a hydraulically binding, two-component waterproofing micro-mortar based on cement, selected aggregate, special additives and water-soluble synthetic resins. CM O2P class according to PN-EN 14891: 2012, PN-EN 14891: 2012 / AC: 2012 - Polymer modified (CM) cement product, impermeable to water, used in a liquid form, with the ability to bridge cracks at low temperature (-20 ° C), resistant to chlorinated water (O2P). For use under ceramic tiles outdoors, on horizontal and vertical surfaces and in swimming pools.

The webertec Superflex D3 micro-mortar is designed to make flexible waterproofing coatings that protect against water and moisture :
- balconies and terraces
- wet rooms (bathrooms, laundries, showers, kitchens, etc.)
- swimming pools
- underground parts of buildings (foundations, benches, basement walls, etc.)
- tanks in sewage treatment plants

The product is intended for indoor and outdoor use.

Application of the product

Webertec Superflex D3 micro-mortar is intended for the production of flexible waterproofing coatings to protect against water and moisture.

• for composite (sub-tile) waterproofing of balconies and terraces,
• for waterproofing humid and wet rooms (showers, bathrooms, swimming pools, etc.),
• for sealing water tanks, including drinking water,
• for sealing and securing tanks in sewage treatment plants,
• for horizontal and vertical waterproofing of underground parts of buildings and structures, such as:
  • continuous footings,
  • foundation walls,
  • foundation slabs.
• for sealing plinth areas of buildings,
• for waterproofing with negative water pressure (tearing off the waterproofing from the substrate) - depth up to 3 m below the groundwater table,
• for secondary insulation of buildings and structures (walls, floors), also bath type,
• as a pre-seal and a bonding layer for polymer-bituminous sealing compounds (KMB),
• for temporary sealing during construction,
• bonding layer on existing bituminous (asphalt) coatings.

The design of the waterproofing depends on the type of waterproofing on construction, moisture / water loads, presence of aggressive media, etc.

The most important properties of the product

• high tightness, also when water pressure detaches the waterproofing from the substrate
• very good adhesion to the substrate
• binds without the appearance of scratches and residual stress, also under wind loads and UV radiation
• flexibility, also at low temperatures (-20?C)
< li> crack-bridging ability, also at subzero temperatures
• frost, aging and UV resistant
• can be further processed after 3-4 hours
• after 24 hours, light foot traffic and tiling
• extremely easy to work with brush, trowel, roller or spraying

Application and setting conditions

Protect the freshly applied waterproofing layer against too quick drying. Avoid strong wind and direct sunlight on the processed surface. You should follow the rules of building art. Protect the fresh waterproofing layer against frost for at least 4 hours.

The freshly applied webertec Superflex D3 layer should also be protected for at least 4 hours against rain (risk of mechanical damage) and moisture (in including condensation). Discoloration may occur on the surface of the coating if exposed to water or moisture. This is a natural phenomenon for polymer-modified mineral products and does not adversely affect the performance of the coating. This phenomenon only affects the appearance of the waterproofing coating.

Safety precautions

The powder component consists of cement. Take measures to prevent dusting or splashing of the mortar. Do not inhale, protect skin and eyes from splashes. It is recommended to use personal protective equipment (glasses, gloves, aprons).
During the work, the health and safety regulations regarding health protection resulting from the relevant ordinances and the provisions of the safety data sheets and labeling on the packaging must be observed.

Translations of product names and their descriptions have been translated using Google Translate.