Tile adhesive WEBER ZP415 25 kg C2TE white

The most important properties of the product: - significantly reduced dusting of the product - for natural stone, ceramic and glass mosaic, white stoneware, glaze and terracotta - increased resistance to discoloration and lime efflorescence - medium-layer, up to 15 mm - for damp and wet rooms and outside - on substrates with increased load - reduced runoff - frost-resistant and waterproof. Application of the product: - Weber ZP415 adhesive mortar was produced in an innovative technology reducing dusting during pouring and mixing, therefore it is especially recommended for working in confined spaces. Significant reduction of dust from cement dust and air dust, improves the comfort of work in a noticeable way and shortens the time of cleaning works. - Weber ZP415 adhesive can be used indoors and outdoors in residential construction and on substrates with increased usable load, e.g. floors in commercial and industrial facilities. It is intended for laying natural and synthetic stones of varying water absorption, ceramic and glass mosaics, stoneware and glaze. The substrate for the cladding can be: - concrete - cement and cement-lime plaster - gypsum plaster - gypsum-cardboard and chip-cement boards - cement and anhydrite screed - OSB boards - old paint coatings - existing ceramic cladding, terrazzo - sub-tile sealing - heating floor - thermal insulation boards - raw surfaces made of small-size elements: bricks, blocks, concrete, ceramic, silicate blocks and other similar construction materials. - The mortar can be used for leveling the surfaces under the tiles to be laid (one layer is 2-15 mm thick) and for building small elements, eg bathtub or shower tray covers, etc. The mortar can be used outdoors, but frost-resistant tiles should be used. Recommendations: For use on surfaces with increased usable load: staircases, lobbies, corridors, kitchens, in humid and wet areas - bathrooms, showers, laundry and outside - balconies, terraces and plinths. The product is not recommended for fixing large-format conglomerates, e.g. 60x120 cm, and ceramic tiles on the facade. To fix the tiles on the facade in the thermal insulation system, use the Weber ZP418 adhesive. Do not apply the mortar on the tile in points. The temperature during application and bonding should not be lower than + 5 ° C and higher than + 25 ° C. during application and bonding, avoid direct sunlight and moisture, protect against rain. Technical data: Mixing ratio: 6.75-7.0L / 25 kg Maturing time: 5 min Open time: 30 min Correction time: 20 min Ready to use time: (temperature approx. 20 ° C) 4 h Minimum thickness: 2 mm Maximum layer thickness: 15 mm Runoff: 0.5 mm Adhesion: 1.0 N / mm 2 Full strength: after 7 days Pedestrian traffic / grouting: after 24 hours Consumption: 2-6 kg / m2 IMPORTANT! Classes of adhesives for tiles: Adhesives are classified on the basis of the European standard PN EN 12004. According to it, adhesive mortars are divided by type and class. There are types of adhesives (due to their chemical composition): C - cement, D - dispersion, R - reactive (based on synthetic resins: polyurethane and epoxy). Due to technical parameters, the classes of adhesives are: 1 - normally binding, 2 - with enhanced parameters. Due to additional requirements, the classes of adhesives are: F - fast-setting, T - with reduced flow, E - with extended open time. Additionally, according to the PN EN 12002 standard, adhesive mortars can be divided according to their transverse deformation into: S1 - deformable adhesives - from 2.5 to 5 mm, S2 - highly deformable adhesives - over 5 mm. Thus, mortar marked with C2 symbol has better adhesion properties than ordinary class C1 mortars. The adhesive marked C2 S1 is additionally characterized by deformability, and C2 S2 - high deformability. Mortar

Translations of product names and their descriptions have been translated using Google Translate.